JOHN DEERE Kohler K241 10 HP engine rebuilt reman. core reqd

 

 

JOHN DEERE Kohler K241 10HP engine block shortblock rebuilt remanufactured core required




See notes below!

This is a brand new rebuild, not a brand new engine!

 

A properly re manufactured engine is as good or better than a new one as ( seasoned ) blocks have less chance of warpage or change as you use them than a new one.

You can't get this quality of work at a local mower shop or dealer as it requires an engine rebuild/machine shop with proper equipment and know how. This is not just a bored out engine with the valves ground but a fully remanufactured block and most of the work done is listed below.

We have a general block pictured below and not the exact one you will get as there are many blocks and configurations available in each brand and application. For this reason we will need a spec as well as ask you a number of questions to make sure we send you a block that is a drop in fit. We have blocks available for most any application to rebuild but it's best to call before buying just to make sure we have in stock.

Call (330) 868-7875 or (330) 956-6830 from 9 to 5 eastern time first to make sure we do have a core for your application. For instance we have dozens of blocks for a John Deere 214 but they have many variations and are not interchangable at all so you need to get the proper block.

Current wait time to ship a block from time of order is 3 to 3 1/2 weeks and this can vary so you can ask that also when you call.

( 2 ways to buy ) 1st you can send us your core up front and avoid a core charge ( we will immediately send you a special shipping box with packing instructions ) and you send us your core within 1 week. ( For this option you should be fairly sure it is rebuildable ( we will let you know if it isn't and show you why with pics ) as if it's not you would still owe some of the core charge.  2nd pay core charge up front, we rebuild and send our block and send to you, you install new block, put your core in our box and call us and we pick it up. Then we determine core refund when it comes back and (most) receive full refund if engine was running and even if blown when block is not cracked by starter or bottom of cylinder broken , but read our note about cores at bottom of ad.

If you send your core to us up front make sure to tell us if you want the exact one back as many times we have a similar engine already 1/2 way done before it gets here and we may ship it back to keep on our time schedule. We sometimes have 30 or more on order at any 1 time and to get out in a timely manor we ship out the quickest way we can unless you specifically specify you want yours back!!!

(NOTE) Balance gears replacement is not included in price and is $40 additional and we will send a Pay Pal invoice or charge card for it if you want. We suggest leaving out as it only matters to have them in on a few applications and we will suggest you have them for those few applications when you order. Most engines don't have balance gears in them as they were an option from Kohler to the OEMS and we make it an option also. They can not be added to any engine that never came from factory without them such as most John Deeres. 

***********************************************************************************************************************************

All blocks are degreased, acid dipped, blasted, and then hot pressure tank washed several times to remove carbon, dirt, rust, and grease for a clean surface to work on.

Critical gasket surfaces are machined flat for a good seal.

Blocks are bored  for a like new fit of piston and rings and new piston and rings installed.!. (Just honing a used bore as many shops do will increase piston to wall clearance and will not correct cylinder out of roundness so just honing and re ringing will not seal as well or last nearly as long as boring and installing new piston and rings with proper clearance)

Valves, guides, and valve seats are all re machined to like new or better specs for a good seal! (just lapping valves and seats will not correct seat and guide or seat and valve misalignment so will last a lot shorter time than re machining)

Governor arms are checked and many repaired or replaced and all engines get a new Governor as they develop stress cracks over time and a used one may be good today but not 6 months down the road.

Crankshafts are all remachined to factory new specs and a new rod installed

Camshaft and lifters are reconditioned and compression release is reconditioned!

Engine is assembled with new piston, rings, rod, governor gear,  gaskets , and seals and other reusable parts inspected and replaced as needed!

Engine is coated with heatproof primer and ready for paint

Next we install new points rod and points and then set points and valve clearance

Balance of gaskets are sent with block so you can reassemble head, oil pan, and other items. 

We are also now sending some assembly tips as we are finding some people getting engine assembled incorrectly such as governor and high speed which we also ask everyone to call us for help setting but the few people that had problems never bothered to call us. These 2 items are critical to get right before starting and we ask everyone to call us before starting!

***********************************************************************************************************************************

Because these are on older machines just ordering for an application or giving a spec number doesn't insure you will get a motor that fits as someone may have adapted another engine to fit. This is why we always ask questions about block to insure we send proper product to you

 

  • Because these are on older machines just ordering for an application or giving a spec number doesn't insure you will get a motor that fits as someone may have adapted another engine to fit. This is why we always ask plenty of questions about block to insure we send proper product to you.

  • Because these are on older machines just ordering for an application or giving a spec number doesn't insure you will get a motor that fits as someone may have adapted another engine to fit. This is why we always ask questions about block to insure we send proper product to you.I

(CORES) 6 years ago 4 out of 5 cores returned were not blown up and rebuildable, so we weren't so picky on cores. Now 4 out of 5 are returned to us blown  and many greatly damaged as people are waiting longer to fix their problem. Also a greater number are coming back all ready rebuilt or worn to the limit and the cost to resleeve a block or weld a crank back to standard is about 3 times the cost to remachine and rebuild. Our prices are low and are based on having a good rebuildable core returned and that is why we charge a core charge. We pretty much have a set refund rate if items are damaged, a block that needs sleeved or thrown away is MINUS $65, a crank with pto end worn out or flywheel end damaged is Minus $50. If cam is broke in half or lobes worn off Minus $25. Our core charge is very reasonable and even if we give nothing back and get a junk block it costs us much more to replace than we are charging you.

Also note that if you buy a 14 HP or 12 HP we must have a like core returned. You can't take your 10 Hp to a shop and have them rebuild it to a 14 Hp and we can't either.


(WARRANTY) Yes we do warranty engine

 

 

CHECK OUT THE MANY OTHER ITEMS WE HAVE FOR SALE IN OUR STORE BY CLICKING ON THE TAB AT TOP RIGHT OF THIS PAGE ( VISIT SELLERS STORE )

 

 

A CREDIT CARD OR PAY PAL IS REQUIRED! CALL (330) 956-6830 or (330) 868-7875 9 TO 5 MONDAY THUR FRIDAY. ITEMS MAY BE PAID COD IN CASH IF PICKED UP AT KUSTOM 1565 UNION AVE. MINERVA,OHIO 44657


WE SHIP MOST NEW PARTS WITHIN 2 TO 3 BUSINESS DAYS UNLESS WE ARE TEMPORARILY OUT OF STOCK. Engines are much longer so ask how long when ordering.  WE CARRY A LARGE INVENTORY BUT DO RUN OUT OCCASIONALLY. STILL ABOUT 99 PERCENT SHIPS WITHIN 2 TO 3 DAYS.


WE HAVE BEEN IN BUSINESS FOR 35 YEARS AT THE SAME LOCATION. WE ARE A PROFESSIONAL ENGINE REBUILD SHOP AND ALSO SUPPLY ENGINE PARTS AS WE CARRY A LARGE INVENTORY FOR SALE AND OUR OWN USE.


IF YOU NEED HELP OR NEED TO SPEAK TO SOMEONE CALL 330 956-6830 or 330 868-7875 FROM 8 TO 4  EASTERN TIME MONDAY THRU FRIDAY! CLOSED SATURDAY AND SUNDAY


 

 

JOHN DEERE Kohler K241 10 HP engine rebuilt reman. core reqd
Click To Enlarge
  • Item #: Jd10
  • Condition: Refurbished
  * Marked fields are required.
*
Qty*
Price $689.00